![]() The second will connect two white neutral wires, while the third will connect the ground wires. The first connector connects the black power wire from the electrical cabinet to the black and blue wires from the fan. You will need three swivel wire connectors for this. Once you have located and identified all the wires in your fan and electrical cabinet, you can start working on their connections. The black wire is hot and the white wire is zero, much like the cables that make up the fan itself. The box should include a black wire, a white wire, and a ground wire made of bare copper. You must recognize the cables in the ceiling box in addition to those on the fan itself. The standard is that the black wire is the fan’s power source, the blue wire is the light supply, the white wire is the neutrality wire, and the green wire is the ground wire, however you should carefully study the instructions for your new fan to be sure. Inside the ceiling fan, you will often find black, white, blue, and green wires. Step 2: Identify your threadsĪlthough the wires within the ceiling fan are very straightforward, you must understand what each one is in order to connect them correctly. The voltage tester should be applied to the black wire inside the electrical box of your fan, as this is usually the hot wire of the power supply. Even if the circuit breakers are marked, it is also good to use a non-contact voltage tester to confirm that the power is off before proceeding, as the circuit breakers may always be marked incorrectly. How to Connect a Ceiling Fan with Lightīefore you can connect your new ceiling fan, you will need to turn off the power to its circuit by switching the correct circuit breaker in the electrical panel of your home. Check that the fan and the light switch work properly and are turned off. Press the power button on the electrical panel’s circuit breaker. Screw the cover plate back to the wall using a screwdriver. Screw the switch to the wall with a screwdriver and the screws provided. Step-11Ĭarefully push the wiring into the wall area with the switch attached. If the connector does not completely cover all unprotected wires, cover them with additional electrical tape to prevent the risk of fire and electric shock. Make sure no wiring is exposed at this point. Step-10Ĭonnect the twist-on connectors to each of the four twist-on wire configurations by twisting them by hand until they completely cover the exposed wires. Step-9Ĭonnect the white wire from the new switch to the two white wires coming out of the wall by manually twisting the three exposed wires together. This black wire must be connected to the fan.Ĭonnect the blue wire from the new switch to the red wire from the wall by twisting the bare ends of the wire by hand. Step-7Ĭonnect the red wire from the new switch to the second black wire from the wall by twisting the bare ends of the wire together. Refer to new switch instructions for specific wire color differences each manufacturer has a different color scheme, which may differ for different switch models. This lower black wire should lead to the electrical panel, not the fan itself. Step-6Ĭonnect the black wire from the new switch to the lower black wire protruding from the wall by twisting the bare ends of the wire by hand. ![]() Unwrap and pull each wire out of the switch. Step-5ĭisconnect the old switch from the wall wires by turning the screws on the back of the switch with a screwdriver. You can also wrap a small piece of tape around each of the four hanging wires and note their connection point on the tape with a pen. Take a picture of the top wiring with a digital camera or phone to remember the wire connections. ![]() Four wires should be connected to the back of the old switch. Temporarily leave the old switch hanging. ![]() Pull the switch so that the connection wiring can be routed. Use a screwdriver to remove the screws holding the old switch to the wall. Using a screwdriver, remove the cover plate from the preceding switch. Verify that power to that power line is completely off by testing the circuit breaker with a non-contact circuit tester. Turn off the circuit breaker to remove power from the appliance circuit. Locate the fan and light circuit breaker on the main electrical panel. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |